Plate Rolling Machines and Sheet Metal Rollers

A plate rolling machine rolls flat sheet and steel plate into cylinders, cones and open curves.

read more

A plate rolling machine rolls flat sheet and steel plate into cylinders, cones and open curves. KNUTH USA carries motorized three-roll machines in several widths, from a narrow shop machine to wide bu...

read more
Call: +1-847-415-3333

Your KNUTH advisory team
Personal reply on the same working day.

  • Family-run since 1923Machine tools worldwide
  • Every machine testedbefore delivery
  • Machines in stockready in Chicago & Houston
  • Own service teamtechnicians in the USA

Selection guide

Enter sheet thickness, width and material – see matching models.

    Values as per data sheet, cylindrical. Cones: lower thickness (see table).

    All models

    ModelSheet widthSteel max.Stainless max.Cone (steel)Roll ØWeight
    KRM AT – Thin sheet
    KRM AT 10/3,041.3 in0.12 in0.06 in0.08 in3.54 in1,058 lb
    KRM AT 12/2,550 in0.1 in0.06 in0.08 in3.54 in1,146 lb
    KRM AT 15/2,061 in0.08 in0.07 in0.07 in3.54 in1,279 lb
    KRM T – Medium sheet
    KRM T 10/4,041.3 in0.16 in0.08 in0.12 in4.33 in2,183 lb
    KRM T 10/5,041.3 in0.2 in0.1 in0.12 in5.12 in2,646 lb
    KRM T 12/5,050 in0.2 in0.1 in0.12 in5.51 in2,976 lb
    KRM T 15/3,061 in0.12 in0.06 in0.08 in4.33 in2,646 lb
    KRM T 15/4,061 in0.16 in0.08 in0.12 in5.51 in3,131 lb
    KRM T 20/2,080.7 in0.08 in0.04 in0.06 in4.33 in3,042 lb
    KRM T 20/4,080.7 in0.16 in0.08 in0.1 in5.51 in3,638 lb
    KRM ST – Heavy plate
    KRM ST 20/680.7 in0.24 in0.08 in*0.08 in6.69 in4,630 lb
    KRM ST 30/5120 in0.2 in0.08 in*0.08 in7.87 in8,818 lb

    * With pre-bending. Smallest bending diameter KRM ST 20/6: 10 in, KRM ST 30/5: 11.8 in.

    Equipment

    standard    optional extra

    KRM AT
    KRM T
    KRM ST
    Rolls

    Hardened, Ø 3.54 in

    Hardened, Ø 4.33–5.51 in

    Hardened, crowned, Ø 6.69–7.87 in

    All: also for stainless steel, grooves for wire and round bar.

    Radius settingvia the rear roll

    Handwheel

    Motorised, digital readout

    Handwheel

    Motorized (up to 6.6 ft), digital readout

    Motorised, scale

    Digital readout, motorised lower roll

    Cones

    Rear roll can be tilted

    Operation

    Foot switch, motor brake, swing-out top roll

    As KRM AT, 3 hp drive

    As KRM AT, geared drive of top and bottom roll, central lubrication

    Safety

    Emergency stop cable around the working area

    FAQ's

    A plate rolling machine rolls flat plate between several rolls into a cylinder, a cone or an open curve. Shops use plate rolling machines for tubes, boiler shells, vessel bodies and curved parts in vessel and tank work, steel fabrication, HVAC and production runs.

    Start with plate thickness, working width and material. Light sheet is handled by a smaller machine, while wide or heavier plate calls for a larger size. Send us a typical part and we will size the right plate rolling machine.

    Yes. Every plate rolling machine gets a documented inspection to European testing standards, and the result is documented before it ships, with the documentation available on request. We confirm the marking and paperwork that apply for the United States when we quote a machine.

    Yes. The motorized drive and simple operation make the three-roll plate rolling machine a good fit for training programs where roll bending of sheet is taught. For a shop's basic equipment it pairs with other sheet metal machines.

    The Americas service team looks after the machine after installation, with parts and technical support from Germany behind it. Parts supply is committed for ten years across the company. Availability and lead time for a particular plate rolling machine are given on request.

    On a three-roll plate rolling machine two driven rolls feed the blank and the third sets the radius. The rolls are motorized, the blank runs through evenly and the curve holds repeatable over the full length. This build is rugged and the right pick for most sheet work in fabrication.

    A three-roll machine bends in several passes and is rugged and cost-effective. A four-roll machine clamps the blank with an extra roll and eases pre-bending. KNUTH relies on motorized three-roll plate rolling machines, which cover the range of general metal and vessel fabrication.

    Mild steel, stainless, aluminum, copper and zinc are rolled, from light sheet through to heavier plate and flat bar. How thick and how wide the plate can be depends on the size of the plate rolling machine.

    On a symmetric build the rolls sit evenly and the blank is rolled to the radius in several passes. With asymmetric adjustment, tighter radii and pre-bending of the leading edge are easier to reach, so less flat remnant is left.

    The three-roll plate rolling machines from KNUTH have a motorized, electrically driven roll drive. The blank runs through evenly, the curve holds repeatable, and greater widths can be rolled without physical effort.

    What a plate rolling machine does in a fab shop

    A plate rolling machine, also called a bending roll, rolls flat sheet or plate between several rolls into a cylinder, a cone or an open curve. The process is called roll bending or plate rolling. The blank passes through the rolls several times and the radius tightens with each pass. That is how tubes, boiler shells, vessel bodies and curved parts get made without a seam around the circumference.

    How three-roll technology works

    KNUTH plate rolling machines run three rolls. Two driven rolls feed the blank, and the third roll sets the radius by how far it presses in. The roll drive is motorized, so the blank runs through evenly and the curve holds repeatable over the full length.

    Which sheet and materials can be rolled?

    The usual sheet and plate materials run on a plate rolling machine: mild steel, stainless, aluminum, copper and zinc. The range goes from light sheet through to heavier plate and flat bar. Plate thickness and working width drive the machine pick. The heavier the plate and the wider the sheet, the larger the machine has to be.

    Industries and shop types we supply

    Plate rolling machines run wherever round or curved parts get made from sheet and plate. Typical work and buyers include:

    Capacity and machine sizes

    KNUTH USA carries motorized three-roll plate rolling machines in several sizes. Smaller builds suit the shop and roll light sheet, while wider machines handle greater working widths and heavier plate. The rated numbers for working width and plate thickness are on the product cards above.

    Why KNUTH USA

    KNUTH is a machine tool supplier, not a machine builder. We pick proven three-roll series and quality-check every machine before delivery. Machine stock and the parts warehouse sit in Lincolnshire outside Chicago, and Houston covers the southern territory with sales and service. You deal with a US point of contact and get advice on working width, plate capacity and equipment instead of a catalog pick. For the full lineup, see the sheet metal processing machines category.

    Service, parts and lead times

    After the sale the Americas service team looks after the machine, backed by local service. Parts supply is committed for ten years across the company. Availability and lead time for a particular plate rolling machine are given on request. Reach us through the contact page for help sizing a plate rolling machine or checking availability.

    Request a quote

    Item No.

    You will receive price and delivery time by email. If we have questions about the equipment, we will call you first. Prefer to talk right away? +1-847-415-3333

    Only for questions about your request.
    For example required equipment or workpiece.

    By submitting, you agree to the processing of your data in accordance with our privacy policy.

    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
    Thank you!

    We have received your request. Here is what happens next:

    1. You will shortly receive a confirmation at
    2. You will receive price and delivery time by email. If we have questions, we will call you first.
    3. No email? Please check your spam folder.

    In a hurry? Call us: +1-847-415-3333

    Something went wrong

    Please refresh the page and try submitting the form again.

    Call

    Request a Consultation

    Our advisory team will get back to you personally on the same business day. Free and without obligation. Prefer to talk right away? +1-847-415-3333

    Only for questions about your request.
    For example machine, workpiece or material.

    By submitting, you agree to the processing of your data in accordance with our privacy policy.

    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
    Thank you!

    We have received your request. Here is what happens next:

    1. You will shortly receive a confirmation at
    2. An advisor will call you, usually on the same business day.
    3. No email? Please check your spam folder.

    In a hurry? Call us: +1-847-415-3333

    Something went wrong

    Please refresh the page and try submitting the form again.