Plate Rolling Machines and Sheet Metal Rollers

A plate rolling machine rolls flat sheet and plate into cylinders, cones and open curves. KNUTH supplies motorised three-roll sheet metal rolling machines in three series: KRM AT for fine, thin sheet, KRM T for thin to m…

read more

A plate rolling machine rolls flat sheet and plate into cylinders, cones and open curves. KNUTH supplies motorised three-roll sheet metal rolling machines in three series: KRM AT for fine, thin sheet,...

read more
Call: +49 4321 609-0

Your KNUTH advisory team
Personal reply on the same working day.

  • Family-run since 1923Machine tools worldwide
  • Every machine testedin Germany before shipping
  • 1,000 machines in stockmany available quickly
  • Own service teamtechnicians from Germany

Selection guide

Enter sheet thickness, width and material – see matching models.

    Values as per data sheet, cylindrical. Cones: lower thickness (see table).

    All models

    ModelSheet widthSteel max.Stainless max.Cone (steel)Roll ØWeight
    KRM AT – Thin sheet
    KRM AT 10/3,01,050 mm3 mm1.5 mm2 mm90 mm480 kg
    KRM AT 12/2,51,270 mm2.5 mm1.5 mm2 mm90 mm520 kg
    KRM AT 15/2,01,550 mm2 mm1.8 mm1.8 mm90 mm580 kg
    KRM T – Medium sheet
    KRM T 10/4,01,050 mm4 mm2 mm3 mm110 mm990 kg
    KRM T 10/5,01,050 mm5 mm2.5 mm3 mm130 mm1,200 kg
    KRM T 12/5,01,270 mm5 mm2.5 mm3 mm140 mm1,350 kg
    KRM T 15/3,01,550 mm3 mm1.5 mm2 mm110 mm1,200 kg
    KRM T 15/4,01,550 mm4 mm2 mm3 mm140 mm1,420 kg
    KRM T 20/2,02,050 mm2 mm1 mm1.5 mm110 mm1,380 kg
    KRM T 20/4,02,050 mm4 mm2 mm2.5 mm140 mm1,650 kg
    KRM ST – Heavy plate
    KRM ST 20/62,050 mm6 mm2 mm*2 mm170 mm2,100 kg
    KRM ST 30/53,050 mm5 mm2 mm*2 mm200 mm4,000 kg

    * With pre-bending. Smallest bending diameter KRM ST 20/6: 255 mm, KRM ST 30/5: 300 mm.

    Equipment

    standard    optional extra

    KRM AT
    KRM T
    KRM ST
    Rolls

    Hardened, Ø 90 mm

    Hardened, Ø 110–140 mm

    Hardened, crowned, Ø 170–200 mm

    All: also for stainless steel, grooves for wire and round bar.

    Radius settingvia the rear roll

    Handwheel

    Motorised, digital readout

    Handwheel

    Motorised (up to 2 m), digital readout

    Motorised, scale

    Digital readout, motorised lower roll

    Cones

    Rear roll can be tilted

    Operation

    Foot switch, motor brake, swing-out top roll

    As KRM AT, 2.2 kW drive

    As KRM AT, geared drive of top and bottom roll, central lubrication

    Safety

    Emergency stop cable around the working area

    FAQ's

    A plate rolling machine rolls flat plate between several rolls into a cylinder, a cone or an open curve. It is used in vessel, tank and steel construction, in heating, ventilation and air conditioning, in locksmithing and in series production.

    That depends mainly on plate thickness, working width and material. Thin sheet is handled by a smaller machine, while wide or heavier plate needs a larger size. Tell us your workpiece and we will recommend the right plate rolling machine.

    Yes. Every plate rolling machine is given a documented inspection and shipped CE-compliant. The declaration of conformity and the full documentation are included in the delivery.

    Yes. The motorised drive and simple operation make the three-roll plate rolling machine well suited to teaching workshops where roll bending of sheet is taught. For a workshop's basic equipment it combines with other sheet metal machines.

    Service is provided by our own service engineers. Common spare parts come from the central warehouse, and a ten year spare parts supply commitment applies. Availability and delivery time for a particular plate rolling machine are given on request.

    On a three-roll plate rolling machine two driven rolls feed the plate and the third sets the radius. The rolls are motorised, the plate runs through evenly and the curve stays repeatable over the full length. This build is robust and the right choice for most sheet work in metalwork.

    A three-roll machine bends in several passes and is robust and economical. A four-roll machine clamps the plate with an additional roll and eases pre-bending. KNUTH relies on motorised three-roll plate rolling machines, which cover the range of general metal and vessel construction.

    Mild steel, stainless steel, aluminium, copper and zinc are rolled, from thin sheet through to heavier plate and flat bar. How thick and how wide the plate may be depends on the size of the plate rolling machine.

    On a symmetric build the rolls are evenly arranged and the plate is rolled to the radius in several passes. With asymmetric adjustment, tighter radii and pre-bending of the leading edge are easier to reach, so less flat remnant is left.

    The three-roll plate rolling machines from KNUTH have a motorised, electrically driven roll drive. The plate runs through evenly, the curve stays repeatable, and greater widths can be rolled without physical effort.

    What is a plate rolling machine?

    A plate rolling machine rolls flat sheet or plate between several rolls into a cylinder, a cone or an open curve. The process is called roll bending or plate rolling. The plate passes through the rolls several times and the radius is tightened step by step. That is how tubes, boiler shells, vessel bodies and curved components are made without a seam around the circumference.

    Three-roll technology: how roll bending works

    KNUTH plate rolling machines work with three rolls. Two driven rolls feed the plate, while the third roll sets the radius by how far it presses in. The roll drive is motorised, so the plate runs through evenly and the curve stays repeatable over the full length.

    Which sheets and materials can be rolled?

    The usual sheet and plate materials of metalwork can be rolled: mild steel, stainless steel, aluminium, copper and zinc. The range runs from thin sheet through to heavier plate and flat bar. Plate thickness and working width decide the machine choice. The thicker the plate and the wider the sheet, the larger the machine has to be.

    Applications and industries

    Plate rolling machines are used wherever round or curved shapes are made from sheet and plate:

    Machine sizes and equipment

    KNUTH supplies motorised three-roll plate rolling machines in several sizes. Smaller builds suit the workshop and roll thin sheet, while wider machines handle greater working widths and heavier plate. The exact figures for working width and plate thickness are given with each machine in the product cards above.

    Why KNUTH

    KNUTH has stood for machine tools for over 100 years. As a supplier we select our ranges carefully and give every plate rolling machine a documented inspection before it is shipped CE-compliant, with the declaration of conformity included in the delivery. You get tested quality at a fair price without compromising on safety. Machines are ready for despatch from our European central warehouse in Germany. For machines covering further steps, see sheet metal processing and the tube and profile rolling machines.

    Service, spare parts and availability

    Service runs through our own service network, with our own service engineers looking after the machines in the field. Common spare parts come from our central warehouse, and a ten year spare parts supply commitment applies. Whether a particular plate rolling machine is available and how quickly it can be delivered, we will tell you on request.

    Request a quote

    Item No.

    You will receive price and delivery time by email. If we have questions about the equipment, we will call you first. Prefer to talk right away? +49 4321 609-0

    Only for questions about your request.
    Optional: details for a more accurate quote
    For example required equipment or workpiece.

    By submitting, you agree to the processing of your data in accordance with our privacy policy.

    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
    Thank you!

    We have received your request. Here is what happens next:

    1. You will shortly receive a confirmation at
    2. You will receive price and delivery time by email. If we have questions, we will call you first.
    3. No email? Please check your spam folder.

    In a hurry? Call us: +49 4321 609-0

    Something went wrong

    Please refresh the page and try submitting the form again.

    Call

    Request a Consultation

    Our advisory team will get back to you personally on the same business day. Free and without obligation. Prefer to talk right away? +49 4321 609-0

    Only for questions about your request.
    For example machine, workpiece or material.

    By submitting, you agree to the processing of your data in accordance with our privacy policy.

    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
    Thank you!

    We have received your request. Here is what happens next:

    1. You will shortly receive a confirmation at
    2. An advisor will call you, usually on the same business day.
    3. No email? Please check your spam folder.

    In a hurry? Call us: +49 4321 609-0

    Something went wrong

    Please refresh the page and try submitting the form again.